EnoughToGet CalculatorsGuides

Roofing & cladding

Roofing sheets calculator

Metal roof sheets: how many sheets of Custom Orb, Trimdek or Klip-Lok, how long they must be for the pitch, screws and ridge capping.

Try itRoofing sheets: enter your own sizes
m
The length of one roof plane, eaves to eaves.
m
Measured flat on the plan, not along the slope.
m
The part of the roof past the wall, measured flat.
°
The angle of the roof in degrees.
Cover width is the width one sheet covers once overlapped, from Lysaght.
Only used for the screw count.
%
You need
30 sheets
96 m² of roof, 4.8 m sheets

Shopping list

ItemBuyNote
Custom Orb (corrugated) sheets, 4.82 m long30 sheets762 mm cover; order the length your supplier can cut (sheets can be supplied long)
Roofing screws506 screws5 per m² at 900 mm supports (Lysaght Table 3.8)
Ridge capping, 2400 mm lengths5 lengthslaps and hip ends not counted
  • Flashings, gutters, end laps and fixing detail depend on your roof and wind region: follow the Lysaght manual.
How this was worked out
  1. Pitch factor: 1 ÷ cos(pitch)
    1 ÷ cos(22.5°) = 1.08 ×
  2. Sheet length (slope): (run + overhang) × pitch factor
    (4 + 0.45) × 1.082 = 4.82 m
  3. Sheets per plane: length ÷ cover width, rounded up
    10000 ÷ 762 = 14 sheets
  4. Sheets: planes × sheets per plane × (1 + waste), rounded up
    2 × 14 × 1.05 = 29.4 sheets
  5. Roof area: planes × length × slope length
    2 × 10 × 4.82 = 96.33 m²
  6. Screws: area × screws per m² × (1 + waste)
    96.3 × 5 × 1.05 = 506 screws

Roofing sheets needed by size

Roof plane (m, length × run)Main resultShopping list
6 × 317 sheet17 sheet Custom Orb (corrugated) sheets, 3.73 m long; 236 screw Roofing screws; 3 length Ridge capping, 2400 mm lengths
8 × 3.524 sheet24 sheet Custom Orb (corrugated) sheets, 4.28 m long; 360 screw Roofing screws; 4 length Ridge capping, 2400 mm lengths
10 × 430 sheet30 sheet Custom Orb (corrugated) sheets, 4.82 m long; 506 screw Roofing screws; 5 length Ridge capping, 2400 mm lengths
12 × 4.534 sheet34 sheet Custom Orb (corrugated) sheets, 5.36 m long; 676 screw Roofing screws; 5 length Ridge capping, 2400 mm lengths
15 × 542 sheet42 sheet Custom Orb (corrugated) sheets, 5.90 m long; 930 screw Roofing screws; 7 length Ridge capping, 2400 mm lengths

Australian figures with every other setting at its default. Change them in the calculator, or switch to New Zealand.

How it is calculated

  1. Pitch factor: 1 ÷ cos(pitch)
    1 ÷ cos(22.5°) = 1.08 ×
  2. Sheet length (slope): (run + overhang) × pitch factor
    (4 + 0.45) × 1.082 = 4.82 m
  3. Sheets per plane: length ÷ cover width, rounded up
    10000 ÷ 762 = 14 sheets
  4. Sheets: planes × sheets per plane × (1 + waste), rounded up
    2 × 14 × 1.05 = 29.4 sheets
  5. Roof area: planes × length × slope length
    2 × 10 × 4.82 = 96.33 m²
  6. Screws: area × screws per m² × (1 + waste)
    96.3 × 5 × 1.05 = 506 screws

What to enter

FieldUnitHelp
Roof length along the eavesmThe length of one roof plane, eaves to eaves.
Horizontal run, eaves to ridgemMeasured flat on the plan, not along the slope.
Eaves overhangmThe part of the roof past the wall, measured flat.
Roof pitch°The angle of the roof in degrees.
Roof shapechoose
Sheet profilechooseCover width is the width one sheet covers once overlapped, from Lysaght.
Purlin or batten spacingchooseOnly used for the screw count.
Extra for cuts%

Before you buy

Frequently asked questions

How do I calculate roofing sheets?

Metal roof sheets: how many sheets of Custom Orb, Trimdek or Klip-Lok, how long they must be for the pitch, screws and ridge capping. Enter your sizes in the calculator. It works out pitch factor (1 ÷ cos(pitch)) and the later steps, then rounds up to whole packs.

Where does the roof cover custom orb figure come from?

762 mm. Lysaght Custom Orb (corrugated) profile: cover width 762 mm. Checked against its source on 2026-11-18.

Where does the roof cover trimdek figure come from?

762 mm. Lysaght Roofing and Walling Installation Manual: Trimdek cover width 762 mm. Checked against its source on 2026-11-18.

Where does the roof cover klip lok 406 figure come from?

406 mm. Lysaght Roofing and Walling Installation Manual: Klip-Lok 406 cover width 406 mm. Checked against its source on 2026-11-18.

Where does the roof cover klip lok 700 figure come from?

700 mm. Lysaght Roofing and Walling Installation Manual: Klip-Lok 700 cover width 700 mm. Checked against its source on 2026-11-18.

Does this calculator work for New Zealand?

Yes. Switch the region to New Zealand. Where New Zealand products or coverage differ, such as Resene paint coverage and GIB plasterboard sheets, the calculator uses the New Zealand figure.

Does it show prices?

No. It gives quantities and a shopping list. Ask your supplier for prices.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
roof cover custom orb762 mmVerified 2026-11-18Lysaght Custom Orb (corrugated) profile: cover width 762 mm.
roof cover trimdek762 mmVerified 2026-11-18Lysaght Roofing and Walling Installation Manual: Trimdek cover width 762 mm.
roof cover klip lok 406406 mmVerified 2026-11-18Lysaght Roofing and Walling Installation Manual: Klip-Lok 406 cover width 406 mm.
roof cover klip lok 700700 mmVerified 2026-11-18Lysaght Roofing and Walling Installation Manual: Klip-Lok 700 cover width 700 mm.
roof screws trimdek 9006 screws/m2Verified 2026-11-18Lysaght Installation Manual Table 3.8: Trimdek needs 6 screws per m2 at 900 mm support spacing.
roof screws trimdek 12005 screws/m2Verified 2026-11-18Lysaght Installation Manual Table 3.8: Trimdek needs 5 screws per m2 at 1200 mm support spacing.
roof screws custom orb 9005 screws/m2Verified 2026-11-18Lysaght Installation Manual Table 3.8: Custom Orb (3 fasteners per sheet width) needs 5 screws per m2 at 900 mm support spacing.
roof screws custom orb 12004 screws/m2Verified 2026-11-18Lysaght Installation Manual Table 3.8: Custom Orb (3 fasteners per sheet width) needs 4 screws per m2 at 1200 mm support spacing.
roof ridge capping length 24002,400 mmVerified 2026-11-18Lysaght Flashing Guide: standard ridge capping lengths 2400 and 1800 mm (Victoria).
roof min pitch custom orb5 degreesVerified 2026-11-18Lysaght Flashing Guide: minimum pitch for Custom Orb is 5 degrees.
roof min pitch trimdek2 degreesVerified 2026-11-18Lysaght Flashing Guide: minimum pitch for Trimdek is 2 degrees.
roof min pitch klip lok 4061 degreesVerified 2026-11-18Lysaght Flashing Guide: minimum pitch for Klip-Lok 406 is 1 degree.
roof min pitch klip lok 7002 degreesVerified 2026-11-18Lysaght Roofing and Walling Installation Manual: Klip-Lok 700 Hi-Strength needs a pitch of 2 degrees (1 in 30) in 0.42 mm steel and 1 degree (1 in 50) in 0.48 and 0.60…
roof waste5 %Editable defaultEditable allowance for cut sheets. No Australian manufacturer figure was found: a common roofing rule of thumb.

Guides for this calculator

Related calculators