EnoughToGet CalculatorsGuides

Fencing & decking

Materials for a 20 m timber paling fence

By the EnoughToGet teamUpdated 2026-11-185 min readSources and assumptions

To build a 20 m timber paling fence that is 1.8 m high, you will need 10 posts, 27 rails (at 2.4 m lengths), 200 palings (100 mm wide), and 20 bags of 20 kg Post Mix concrete.

Try itFence: enter your own sizes
m
The total length of the fence line, gates included.
mm
Up to 1800 mm. Check your council for height limits near boundaries.
Steel panels follow the Lysaght fence installation guide.
mm
Timber shrinks, so many builders leave a small gap. 0 means edge to edge.
You need
10 posts
for 20 m of fence

Shopping list

ItemBuyNote
Posts10 postsat most 2.4 m apart; about 600 mm in the ground
Rails, 2.4 m lengths27 rails3 per bay at 1800 mm high
Palings, 100 mm wide200 palingsedge to edge
Post Mix concrete, 20 kg bags (post holes)20 bags2 bags a hole, for a hole 2 × the post width
  • The 2-bag figure is Bunnings Post Mix advice for a hole 2 × the post width. A wider or deeper hole needs more bags.
How this was worked out
  1. Panels (bays): length ÷ post spacing, rounded up
    20000 ÷ 2400 = 9 bays
  2. Posts: bays + 1
    9 + 1 = 10 posts
  3. Rails: bays × rails per bay
    9 × 3 = 27 rails
  4. Palings: length ÷ (paling width + gap), rounded up
    20000 ÷ (100 + 0) = 200 palings
  5. Concrete for posts: posts × bags per hole
    10 × 2 = 20 bags

Timber Paling Fence Requirements

When planning a timber paling fence, the primary components consist of posts, rails, and the palings themselves. For a standard 1.8 m high fence, the structural integrity depends on the spacing of the posts and the number of horizontal rails used to support the vertical palings.

Timber Queensland TDS 20 Residential Timber Fences specifies that for fences between 1200 mm and 1800 mm high, posts should be set about 600 mm deep. For shorter fences up to 1200 mm high, a depth of 450 mm is sufficient. The maximum post spacing for rails measuring 100 x 38 mm is 2400 mm. If you choose to use 75 x 38 mm rails, the maximum spacing reduces to 2100 mm.

The number of rails required changes based on the height of the fence. Timber Queensland TDS 20 Residential Timber Fences states that two rails are sufficient for paling fences up to 1200 mm high. However, for fences over 1200 mm and up to 1800 mm high, three rails are required. Common paling sizes for these projects include 100 x 15 mm and 75 x 15 mm.

Concrete and Post Installation

Securing the posts in the ground requires adequate concrete. The Bunnings Easy Mix Post Mix technical data sheet provides specific guidelines for this. It states that the hole width should be twice the width or diameter of the post. For the installation of each post, the technical data sheet recommends using approximately two 20 kg bags of Post Mix per hole.

When calculating your total concrete needs, you must multiply the number of posts by the bags required per hole. For a 20 m fence requiring 10 posts, this results in 20 bags of 20 kg Post Mix. If you are using a different type of concrete, such as a standard concrete mix, you should refer to the slab calculator on this site to determine the volume required, as the Boral and Cement Australia concrete mix figures differ from the Post Mix figures.

Steel Sheet Fence Alternative

An alternative to timber palings is the use of steel fence sheets. This method often involves using 3-sheet panels. According to the Lysaght fence and gate installation guide (non-cyclonic), a 3-sheet panel has a width of 2350 mm, which corresponds to the post spacing. Other configurations include 2-sheet panels with a width of 1582 mm and 4-sheet panels with a width of 3100 mm.

For a 20 m fence using the 3-sheet panel style, the requirements shift to 9 panels and 27 steel fence sheets. The number of posts remains the same at 10, and the concrete requirement remains 20 bags of 20 kg Post Mix. Choosing between timber and steel depends on your desired aesthetic and the specific panel widths available from your supplier.

Post depth and how the concrete is counted

Two sourced figures decide the concrete. Timber Queensland's residential fence guide has timber posts set about 600 mm into the ground, and Bunnings' Post Mix data sheet says to dig the hole to one third of the post's length and twice the post's width, using about two 20 kg bags per hole. The calculator multiplies the posts by those two bags, which is why a 20 m fence with 10 posts shows 20 bags. A wider or deeper hole takes more concrete, so treat the bag count as the minimum for a hole of that size and check the data sheet for your own post. Fence posts also differ from slabs: Post Mix is a different product from slab concrete mix, with its own yield per bag, so do not use these bag counts to estimate a slab.

Material Summary Table

The following table outlines the materials required for a 20 m fence at a height of 1.8 m for both timber and steel options.

Material TypeTimber Paling FenceSteel Sheet Fence (3-sheet)
Posts10 posts10 posts
Rails (2.4 m lengths)27 railsN/A
Palings (100 mm wide)200 palingsN/A
Steel SheetsN/A27 sheets
Steel PanelsN/A9 panels
Post Mix Concrete (20 kg bags)20 bags20 bags

Worked Example

To understand how the calculator arrives at these figures, we can look at the 20 m timber paling fence scenario.

First, we determine the number of bays. For a 20 m fence with a maximum post spacing of 2.4 m, the calculation results in 9 bays.

Next, we calculate the posts. With 9 bays, you need 10 posts (one for each end and one for each internal bay).

Then, we calculate the rails. For a fence height of 1.8 m, three rails are required per bay. With 9 bays, this equals 27 rails.

For the palings, the 20 m length is divided by the 100 mm width. This results in 200 palings.

Finally, for the concrete, the 10 posts each require 2 bags of 20 kg Post Mix, totaling 20 bags.

Common Mistakes

One frequent error is underestimating the number of rails needed for taller fences. While two rails may suffice for a 1.2 m fence, a 1.8 m fence requires three rails to maintain structural integrity. Another common mistake is incorrect post hole sizing. The Bunnings Easy Mix Post Mix technical data sheet clarifies that the hole width must be double the post width; digging a hole that is too narrow will result in insufficient concrete coverage.

Frequently Asked Questions

How deep should I bury my fence posts?

For fences between 1200 mm and 1800 mm high, Timber Queensland TDS 20 Residential Timber Fences recommends a post depth of about 600 mm. For fences up to 1200 mm high, a depth of 450 mm is sufficient.

How many rails do I need for a 1.8 m fence?

According to Timber Queensland TDS 20 Residential Timber Fences, fences over 1200 mm and up to 1800 mm high require three rails.

What is the maximum spacing for timber posts?

Timber Queensland TDS 20 Residential Timber Fences states that rails measuring 100 x 38 mm allow for a maximum post spacing of 2400 mm. If using 75 x 38 mm rails, the maximum spacing is 2100 mm.

How much concrete do I need per post hole?

The Bunnings Easy Mix Post Mix technical data sheet suggests using approximately two 20 kg bags per post hole.

What is the width of a 3-sheet steel fence panel?

The Lysaght fence and gate installation guide (non-cyclonic) specifies that a 3-sheet panel has a width of 2350 mm.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
fence timber post spacing max2.4 mVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: rails 100 x 38 mm allow 2400 mm max post spacing (2100 mm with 75 x 38 mm rails).
fence timber rails up to 12002 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: two rails for paling fences up to 1200 mm high.
fence timber rails over 12003 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: fences over 1200 mm and up to 1800 mm high require three rails.
fence paling width 100100 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling width 7575 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling gap default0 mmEditable defaultPalings are laid edge to edge by default. Timber shrinks, so many builders leave a small gap; type your own gap.
fence steel panel width 2sheet1,582 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 1582 mm with 2 infill sheets.
fence steel panel width 3sheet2,350 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 2350 mm with 3 infill sheets (post spacing = panel width).
fence steel panel width 4sheet3,100 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 3100 mm with 4 infill sheets.
concrete post bags per hole2 bags (20 kg)Verified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: use approximately two 20 kg bags per post hole.
concrete post hole width factor2 x post widthVerified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: hole width = 2 x width or diameter of the post.
fence timber post depth600 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: posts about 600 mm deep for fences 1200-1800 mm high (450 mm up to 1200 mm).

Keep reading