EnoughToGet CalculatorsGuides

Landscaping

How many pavers do I need for a 4 x 3 m patio?

By the EnoughToGet teamUpdated 2026-11-186 min readSources and assumptions

To calculate the materials for a 4 x 3 m patio, you need to account for the surface area of the pavers, the volume of the compacted road base, and the volume of the bedding sand based on specific depth requirements.

Try itPavers: enter your own sizes
m
Type metres, for example 4.5.
m
The shorter side.
Pavers per square metre include the joints, from Adbri Masonry paving data.
%
Patterns and curves need more.
You need
79 pavers
12.0 m² at 6.25 per m²

Shopping list

ItemBuyNote
Pavers, 400 × 400 mm79 pavers6.25 per m² including joints
Road base (75 mm compacted depth)2.16 t0.90 m³
Bedding sand (25 mm)0.44 t0.30 m³
  • Allow a fall of at least 2% for drainage, and dig about 170 mm deep for a patio base, bedding sand and the paver.
How this was worked out
  1. Area: length × width
    4 × 3 = 12 m²
  2. Pavers needed: area × pavers per m²
    12.00 × 6.25 = 75 pavers
  3. With waste: pavers × (1 + waste), rounded up
    75.0 × 1.05 = 78.75 pavers
  4. Road base: area × depth ÷ 1000 × density
    12.00 × 75 mm × 2.4 t/m³ = 2.16 t
  5. Bedding sand: area × depth ÷ 1000 × density
    12.00 × 25 mm × 1.45 t/m³ = 0.44 t

Understanding the Dimensions of Your Patio

When planning a small patio, the first step is determining the total surface area. For a standard 4 m by 3 m area, the total surface area is 12 m². Knowing this figure is essential because it dictates the quantity of pavers required and the volume of the underlying layers. While the surface area remains constant regardless of the paver size you choose, the number of individual units will vary significantly.

For example, if you choose a 400 x 400 mm paver, the Adbri Masonry paving brochure (VIC) states there are 6.25 units per m². For a 600 x 400 mm paver, that figure drops to 4.16 units per m². If you opt for a smaller 200 x 100 mm paver, the count increases to 50 units per m². Selecting the correct paver size is a balance between the aesthetic you want to achieve and the amount of cutting required to fit the perimeter of your 12 m² space.

Excavation and Fall Requirements

Before laying any materials, you must prepare the ground. The Adbri Masonry paving brochure (VIC) suggests excavating approximately 170 mm deep to accommodate the layers of road base, bedding sand, and the pavers themselves. This depth ensures that once all your layers are compacted and laid, the finished surface sits at the correct height relative to your surrounding ground level.

Proper drainage is also a critical component of the installation. To ensure water runs off the surface correctly, the Adbri Masonry paving brochure (VIC) specifies a minimum gradient of 2%. This equates to a fall of 100 mm per 5 lineal metres. Failing to account for this fall can lead to water pooling on your new surface, which can cause issues with moisture and longevity. When planning your 4 x 3 m area, you must ensure the ground is graded so that the water flows away from your home or other structures.

Road Base and Bedding Sand Layers

A stable patio requires a solid foundation. The Adbri Masonry paving brochure (VIC) recommends a compacted road base with a minimum depth of 75 mm for a flexible installation. This layer provides the structural integrity for the patio, preventing the pavers from shifting or sinking over time. This is a compacted depth, meaning the material must be rolled or compacted to reach the required thickness.

On top of the road base, a layer of bedding sand is required. The Adbri Masonry paving brochure (VIC) specifies a nominal depth of 25 mm for this layer. While some checklists may allow for 30 mm, using the 25 mm figure ensures you have the correct volume for a standard installation. This sand layer acts as the bed upon which the pavers sit, allowing for slight adjustments to ensure a level surface.

To calculate the weight of these materials, you must consider their density. Australian Native Landscapes provides a product weights FAQ stating that compacted road base has a density of 2.4 t/m³. For the bedding sand, the same source indicates a density of 1.45 t/m³. These figures are vital for ordering the correct tonnage from your supplier.

Material Quantities for a 12 m² Patio

The following table shows the required materials for a 4 x 3 m (12 m²) patio based on different paver sizes, including the necessary road base and bedding sand.

Paver SizePavers Needed (Base)Pavers with 5% WasteRoad Base (75 mm)Bedding Sand (25 mm)
400 x 400 mm75 pavers78.75 pavers2.16 t0.44 t
600 x 400 mm49.92 pavers52.42 pavers2.16 t0.44 t
200 x 100 mm600 pavers630 pavers2.16 t0.44 t

Worked Example: 400 x 400 mm Pavers

To understand how these figures are reached, here is a step-by-step breakdown for a 4 x 3 m patio using 400 x 400 mm pavers.

  1. Calculate Area: 4 m x 3 m = 12 m².
  2. Calculate Base Paver Count: Using the Adbri Masonry paving brochure (VIC) figure of 6.25 pavers per m², multiply 12 m² by 6.25 to get 75 pavers.
  3. Calculate Waste: The Adbri Masonry Ultimate Outdoor Planning Guide recommends adding 5% for cuts and breakages. Multiply 75 by 1.05 to get 78.75 pavers.
  4. Round for Purchase: You would need to purchase 79 pavers.
  5. Road Base Weight: For a 12 m² area at a 75 mm depth, the calculator determines you need 2.16 t of road base.
  6. Bedding Sand Weight: For a 12 m² area at a 25 mm depth, the calculator determines you need 0.44 t of bedding sand.

Planning for Larger Areas

If your project exceeds the 4 x 3 m dimensions, the volume of materials increases proportionally. For a larger 6 x 5 m patio (30 m²), the requirements change significantly. Using 400 x 400 mm pavers for a 30 m² area requires 187.5 pavers before waste. With the 5% waste factor, the total is 196.88 pavers, meaning you should purchase 197.

Common Mistakes

One of the most frequent errors in patio construction is failing to account for the depth of the materials. If you do not excavate the full 170 mm suggested by the Adbri Masonry paving brochure (VIC), your finished surface may sit higher than intended or may not have enough room for the 75 mm road base and 25 mm sand layers. This can lead to a surface that is uneven with your surrounding lawn or garden beds.

Another common mistake is neglecting the waste factor. The Adbri Masonry Ultimate Outdoor Planning Guide advises ordering an extra 5% for cuts and breakages. If you order the exact number of pavers required for the area without this buffer, you may run short when cutting pavers to fit edges or corners. It is always safer to have a few extra pavers on hand to ensure you can complete the job without a second delivery.

Finally, ensure you are using the correct density figures for your materials. Using the wrong weight-to-volume ratio can lead to significant under-ordering or over-ordering of road base and sand. Always verify the density of the specific products you are buying with your supplier to ensure your calculations remain accurate.

Frequently Asked Questions

How deep do I need to dig for my patio?

The Adbri Masonry paving brochure (VIC) suggests excavating approximately 170 mm deep to accommodate the road base, bedding sand, and the pavers.

What is the minimum fall required for drainage?

The Adbri Masonry paving brochure (VIC) states a minimum gradient of 2%, which is 100 mm per 5 lineal metres.

How much waste should I add to my paver order?

The Adbri Masonry Ultimate Outdoor Planning Guide recommends ordering an extra 5% for cuts and breakages.

What is the required depth for the road base?

For a flexible installation, the Adbri Masonry paving brochure (VIC) recommends a compacted road base of at least 75 mm.

What is the standard depth for bedding sand?

The Adbri Masonry paving brochure (VIC) specifies a nominal depth of 25 mm for bedding sand in a flexible installation.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
paver per m2 400x4006.25 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Euro Stone 400 x 400 x 40 mm, 6.25 units per m2.
paver per m2 600x4004.16 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Euro Stone 600 x 400 x 40 mm, 4.16 units per m2.
paver per m2 400x20012.5 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Havenslab 400 x 200 x 40 mm, 12.50 units per m2.
paver per m2 200x10050 pavers/m2Verified 2026-11-18Adbri Masonry paving brochure (VIC): Havenbrick 200 x 100 x 40 mm, 50 units per m2.
paver waste5 %Verified 2026-11-18Adbri Masonry Ultimate Outdoor Planning Guide: with the Concrete Masonry Association of Australia, order an extra 5% for cuts and breakages.
paver roadbase depth75 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) flexible installation: compacted road base min 75 mm (also 'enough for 75 mm compacted depth' in its how-to checklist).
paver bedding sand depth25 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) flexible installation cross section: bedding sand nominal 25 mm (its how-to checklist allows sand for 30 mm).
paver excavation depth170 mmVerified 2026-11-18Adbri Masonry paving brochure (VIC) how to lay pavers, step 1: excavate approx. 170 mm deep.
paver min fall2 %Verified 2026-11-18Adbri Masonry paving brochure (VIC): minimum gradient 2% (100 mm per 5 lineal metres).
landscape density roadbase compacted2.4 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: road base/DGB/FCR 2.4 t/m3 (compacted figure).
landscape density sand brickies1.45 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: brickies sand 1.45 t/m3.

Keep reading