EnoughToGet CalculatorsGuides

Concrete & masonry

What is reo mesh, and how many sheets for a slab?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

Reo mesh is steel reinforcing mesh sold in 6.0 x 2.4 m sheets (SL62, SL72 and SL82), and the calculator counts each sheet as covering an effective 5.8 x 2.4 m, or 13.92 m², so a 6 x 4 m slab takes 2 SL72 sheets.

Try itReo mesh: enter your own sizes
m
Type metres, for example 6.5.
m
The slab design names the mesh. All three come as 6.0 × 2.4 m sheets.
You need
2 sheets
54 bar chairs

Shopping list

ItemBuyNote
SL72 mesh sheets2 sheets41 kg each, 82 kg in all
Bar chairs54 chairs800 mm grid
  • A sheet is 6.0 × 2.4 m but laps cost length: this counts the 13.92 m² effective area. Lap length is about 225 mm (Marshall Steel; other guides quote longer laps): your engineer's drawing gives the figure.
  • Bar chairs at no more than 800 mm centres (NCC 2019 Volume Two). Concrete cover: 50 mm bottom and 40 mm top for a slab on ground (Cement Australia).
How this was worked out
  1. Slab area: length × width
    6 × 4 = 24 m²
  2. Effective sheet area: effective length × effective width
    5.8 × 2.4 = 13.92 m²
  3. Sheets: area ÷ effective sheet area, rounded up
    24.00 ÷ 13.92 = 1.72 sheets
  4. Bar chairs: (length ÷ spacing, rounded up, + 1) × (width ÷ spacing, rounded up, + 1)
    (ceil(6 ÷ 0.8) + 1) × (ceil(4 ÷ 0.8) + 1) = 54 chairs

What is reo mesh?

Reo mesh is steel reinforcing mesh supplied in sheets. The sheets come as SL62, SL72 and SL82. SL72 mesh has 6.75 mm wires at 200 mm, and SL82 has 7.6 mm wires at 200 mm. Each type has its own mass per sheet. An SL62 sheet has a mass of 33 kg, an SL72 sheet has a mass of 41 kg, and an SL82 sheet has a mass of 52 kg. A sheet is 6.0 x 2.4 m, but the usable area is smaller because laps cost length. The calculator on this site uses SL72 mesh sheets in its shopping list for each of the slabs in this guide.

Effective sheet area and lap requirements

When calculating the amount of mesh required for a slab, you cannot use the full 6.0 x 2.4 m dimensions of a sheet. This is because laps cost length. The effective area for SL72 and SL82 mesh is 5.8 x 2.4 m, which equals 13.92 m². Marshall Steel provides a guide stating a minimum lap of 225 mm between mesh sheets on residential slabs, though Danterr says about 300 mm. Your engineer's drawing gives the lap length for your project. The calculator counts each sheet at the 13.92 m² effective area rather than the full 6.0 x 2.4 m sheet.

Bar chairs and concrete cover

The calculator counts bar chairs at no more than 800 mm centres. The NCC 2019 Volume Two, clause 3.2.3.2(f)(v), gives bar chairs at no more than 800 mm centres for steel fabric. The number of chairs depends on the dimensions of your slab. For example, a 6 x 4 m slab needs 54 bar chairs. Cement Australia states that reinforcement should be at least 5 cm above the compacted base, which is 50 mm. It also says the reinforcement should be around 4 cm below the top of the slab, which is 40 mm. Cement Australia adds that you should leave 5 cm, or 50 mm, between the formwork and the ends of the bars.

Slab calculations for different sizes

The number of sheets varies with the total area of the slab. For a 3 x 3 m slab, the area is 9 m². Dividing this by the effective sheet area of 13.92 m² gives 0.65 sheets, so you purchase 1 sheet. For a 6 x 4 m slab, the area is 24 m². Dividing 24 m² by 13.92 m² gives 1.72 sheets, so you purchase 2 sheets. For a 10 x 6 m slab, the area is 60 m². Dividing 60 m² by 13.92 m² gives 4.31 sheets, so you purchase 5 sheets.

Slab DimensionsSlab AreaEffective Sheet AreaSheets RequiredBar Chairs
6 x 4 m24 m²13.92 m²254
3 x 3 m9 m²13.92 m²125
10 x 6 m60 m²13.92 m²5126

Worked example

This section walks through the calculation for a 6 x 4 m slab to show how the final sheet count is reached.

First, calculate the slab area by multiplying the length by the width: 6 m × 4 m = 24 m². Next, find the effective sheet area, which is the effective length times the effective width: 5.8 m × 2.4 m = 13.92 m². Then, divide the slab area by the effective sheet area: 24.00 ÷ 13.92 = 1.72 sheets. Finally, round the result up to the next whole number: 2 sheets of SL72 mesh.

For the bar chairs, the calculator works out (length ÷ spacing, rounded up, + 1) × (width ÷ spacing, rounded up, + 1). That is (ceil(6 ÷ 0.8) + 1) × (ceil(4 ÷ 0.8) + 1) = 54 chairs.

Common mistakes

A frequent mistake is using the full sheet dimensions of 6.0 x 2.4 m instead of the effective area of 13.92 m². Because laps cost length, the full sheet size overstates the area each sheet covers. Another error is forgetting to round up the final sheet count. Even if the calculation results in 0.65 sheets, as for the 3 x 3 m slab, you must purchase 1 sheet. Bar chairs are a separate count from sheets. For a 10 x 6 m slab, the calculator gives 126 bar chairs at no more than 800 mm centres. For specific sheet sizes and weights beyond those in this guide, check your product label or supplier.

Frequently asked questions

What is the effective area of SL72 mesh?

The effective area is 5.8 x 2.4 m, which equals 13.92 m².

How many bar chairs are needed for a 3 x 3 m slab?

A 3 x 3 m slab requires 25 bar chairs.

What is the minimum lap for reo mesh?

Marshall Steel suggests a minimum lap of 225 mm for residential slabs. Your engineer's drawing gives the lap for your project.

How much concrete cover is needed at the bottom?

Cement Australia states the reinforcement should be at least 5 cm, or 50 mm, above the compacted base.

What is the mass of an SL82 mesh sheet?

An SL82 mesh sheet has a mass of 52 kg per sheet.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.