EnoughToGet CalculatorsGuides

Paint & plaster

How many screws per plasterboard sheet?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

For one 2400 × 1200 mm sheet, which covers 2.88 m², the calculator's 8 screws per m² gives 24 screws, and a 15 m by 2.4 m wall of 36 m² comes to 317 screws once the 10% waste allowance is inside the figure.

Try itPlasterboard: enter your own sizes
m
Add up the length of every wall you are lining. A 4 × 3.5 m room has 15 m of wall.
m
m²
Leave at 0 if you are only lining walls.
m²
Doors and windows. Many builders do not deduct small openings, because the offcuts are useful.
Thickness does not change the number of sheets, only the weight and the use.
Sheets are 1200 mm wide.
Wideline sheets are a New Zealand GIB product.
%
Rooms with many corners and openings waste more.
You need
1 sheet
2.9 m² to line

Shopping list

ItemBuyNote
Plasterboard 10 mm, 1200 × 2400 mm1 sheet2.88 m² each
Plasterboard screws24 screws8 per m², a rule of thumb: check the maker's guide
Jointing compound, 20 kg packs1 pack0.7 kg for topping and base coat
Cornice (length of wall to cover)1.2 mCornice lengths vary by product: divide by the length you buy
  • For ceilings, Gyprock's guidance is framing at no more than 450 mm centres with fasteners at no more than 300 mm. Check your product's installation guide for walls.
How this was worked out
  1. Area to line: wall length × height + ceiling − openings
    1.2 × 2.4 + 0 − 0 = 2.88 m²
  2. One sheet: width × length
    1.2 × 2.4 = 2.88 m²
  3. Sheets: area × (1 + waste) ÷ sheet area, rounded up
    2.88 × 1.00 ÷ 2.880 = 1 sheets
  4. Screws: area × (1 + waste) × screws per m²
    2.9 × 8 = 24 screws
  5. Jointing compound: area × (topping + base coat per m²)
    2.9 × (0.1 + 0.16) = 0.75 kg

How the screw count is worked out

The calculator does not count screws stud by stud. It starts with the area to line, using wall length × height + ceiling − openings. For a 1.2 m by 2.4 m wall that is 2.88 m². It then multiplies that area, with waste included, by 8 screws per m². The 8 is the calculator's starting rate, matching the GIB site guide figure of approximately 800 screws per 100 m² of plasterboard. On the small wall the sum is 2.9 × 8, which comes to 23.2 and is returned as 24 screws. Sheet count is a separate step: area × (1 + waste) ÷ sheet area, rounded up. Screws run off the lined area, so a room's screw figure is simply the larger area carried through the same multiplication.

What changes the answer

Three things move the screw count: the area to line, the waste allowance and the screws per m² rate. Area comes from wall length × height + ceiling − openings, so a longer or taller room raises the count in proportion. Waste is editable and sits at 10% to begin with; it enters as (1 + waste), which turns 36 m² into 39.6 m² for the screw sum. The rate itself is editable too, and 8 per m² is where it starts. Sheet size shifts the sheet count rather than the screw count: 1200 × 2400 mm is 2.88 m², and Gyprock's Standard 13 mm page lists widths of 900, 1200, 1350 and 1400 mm with lengths from 2400 mm to 6000 mm. In New Zealand, GIB Wideline Standard is 1350 mm wide in 10 and 13 mm.

Screws per sheet and per room

Two runs from the calculator show the jump from a single sheet to a wall. The first has no waste allowance and covers exactly one sheet area; the second uses the 10% waste starting value on a 36 m² wall.

JobArea to lineWasteSheetsScrews
1.2 m × 2.4 m wall2.88 m²0%124
15 m × 2.4 m wall36.0 m²10%14 (13.75 before rounding up)317

Both rows also return jointing compound — 0.75 kg on the small wall and 9.36 kg on the 36 m² wall — against 20 kg packs. The screw column is the area including waste multiplied by 8: 2.9 × 8 in the first row, 39.6 × 8 in the second. Sheets and screws round at different points, since 13.75 sheets has to go up to 14, while the screw sums settle at 24 and 317.

Worked example

Take the 1.2 m by 2.4 m wall.

  1. Area to line = wall length × height + ceiling − openings = 1.2 × 2.4 + 0 − 0 = 2.88 m².
  2. One sheet = width × length = 1.2 × 2.4 = 2.88 m².
  3. Sheets = area × (1 + waste) ÷ sheet area, rounded up = 2.88 × 1.00 ÷ 2.880 = 1 sheet. The 1.00 already contains the waste allowance, which is 0% here, so nothing extra is added on top.
  4. Screws = area × (1 + waste) × screws per m² = 2.9 × 8 = 23.2, returned as 24 screws. This multiplier carries the waste as well.
  5. Jointing compound = area × (topping + base coat per m²) = 2.9 × (0.1 + 0.16) = 0.75 kg, which the shopping list rounds to one 20 kg pack.

Common mistakes

Dividing the wall by the sheet and stopping there: 36 ÷ 2.88 = 12.5 sheets, but the (1 + waste) step takes it to 13.75, which rounds up to 14. Rounding that down to 13 falls short of the 13.75 sheets the area × (1 + waste) step asks for.

Adding waste twice to screws: 317 already includes the 10%, because the sum uses 39.6 m² and not 36 m². Multiplying 317 by another 1.1 gives 348.7, which counts the offcuts twice.

Mixing units: 2400 × 1200 mm is 2.88 m², and it has to be expressed in square metres before it can divide into a wall area given in square metres.

Carrying the wrong waste figure between runs: the small example has waste set to 0 and the room example to 10%, so their totals are not comparable.

Treating the rate as fixed: 8 per m² is the calculator's starting value and can be edited.

Frequently asked questions

How many screws do I need for one plasterboard sheet?

A 1200 × 2400 mm sheet covers 2.88 m², and at 8 screws per m² the calculator returns 24 screws — the sum is 2.9 × 8, rounded up from 23.2.

How many screws for a whole room?

For a 15 m by 2.4 m wall, 36 m² with no ceiling or openings added, the calculator returns 317 screws from 39.6 m² × 8. The 39.6 already includes the 10% waste allowance, so nothing further is added.

Where does the 8 screws per m² figure come from?

The GIB site guide gives fastenings coverage of approximately 800 screws per 100 m² of plasterboard, which is the same as 8 per m². It is the calculator's starting value and it can be edited.

Does the 300 mm fastener spacing change the count?

The calculator counts from area, not from spacing. For ceilings, Gyprock's FAQ gives fasteners at no more than 300 mm centres and framing at no more than 450 mm centres. GIB's general wall and ceiling installation guide gives 300 mm maximum centres around the sheet perimeter, with stud centres not exceeding 600 mm for horizontal fixing in New Zealand. Check your product's installation guide for walls.

Do New Zealand sheet sizes change the screw count?

GIB Wideline Standard is 1350 mm wide in 10 and 13 mm, so a sheet is wider than the 1200 mm used in the worked example. The screw count still runs off the area to line multiplied by the screws per m² rate, so the lined area is what sets the number.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
plasterboard sheet width1,200 mmVerified 2026-11-18Gyprock Standard 13 mm product page lists widths 900, 1200, 1350, 1400 mm; 1200 is the common width (Plus also lists 1200 and 1350).
plasterboard sheet length 24002,400 mmVerified 2026-11-18Gyprock Standard 13 mm product page lists lengths 2400, 2700, 3000, 3600, 4200, 4800, 6000 mm (stocked sizes vary by region).
plasterboard sheet length 27002,700 mmVerified 2026-11-18Gyprock Standard 13 mm product page lists lengths 2400, 2700, 3000, 3600, 4200, 4800, 6000 mm (stocked sizes vary by region).
plasterboard sheet length 30003,000 mmVerified 2026-11-18Gyprock Standard 13 mm product page lists lengths 2400, 2700, 3000, 3600, 4200, 4800, 6000 mm (stocked sizes vary by region).
plasterboard sheet length 36003,600 mmVerified 2026-11-18Gyprock Standard 13 mm product page lists lengths 2400, 2700, 3000, 3600, 4200, 4800, 6000 mm (stocked sizes vary by region).
plasterboard sheet width wideline1,350 mmVerified 2026-11-18GIB site guide (April 2024): GIB Wideline Standard is 1350 mm wide in 10 and 13 mm.
plasterboard waste10 %Editable defaultcommon trade rule of thumb for cuts and offcuts, editable
plasterboard screws per m28 screws/m2
New Zealand: 8 screws/m2
Editable defaultno Gyprock figure found; taken from GIB site guide (approx. 800 screws per 100 m2), editable
plasterboard topping per m20.1 kg/m2Verified 2026-11-18Gyprock Jointmaster topping page: 20 kg pail (12 L approx.), coverage 10 kg per 100 m2.
plasterboard basecoat per m20.16 kg/m2Verified 2026-11-18Gyprock Base Coat 20/45/60/90 page: coverage approx 16 kg per 100 m2; 20 kg packs.
plasterboard compound pack20 kgVerified 2026-11-18Gyprock Base Coat 20/45/60/90 page: Base Coat 45, 60 and 90 sold in 20 kg packs.
plasterboard cornice length3.6 mVerified 2026-11-18GIB site guide (April 2024), GIB-Cove: all profiles available in 3.6 m lengths.
plasterboard framing centres max450 mmVerified 2026-11-18Gyprock FAQ (alfresco ceilings answer): install to AS 4055 with maximum framing centres of 450 mm.
framing stud spacing max600 mmVerified 2026-11-18GIB general wall and ceiling installation guide: stud centres must not exceed 600 mm (horizontal fixing); framing to comply with NZS 3604:2011. NZS 3604 text itself not…
plasterboard fastener spacing max300 mm
New Zealand: 300 mm
Verified 2026-11-18Gyprock FAQ (alfresco ceilings answer): fasteners at a maximum of 300 mm centres.

Keep reading