EnoughToGet CalculatorsGuides

Fencing & decking

How many fence posts do I need?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

For a 10-metre timber fence built at 2.4-metre bays, the calculator determines you need 6 posts.

Try itFence: enter your own sizes
m
The total length of the fence line, gates included.
mm
Up to 1800 mm. Check your council for height limits near boundaries.
Steel panels follow the Lysaght fence installation guide.
mm
Timber shrinks, so many builders leave a small gap. 0 means edge to edge.
You need
10 posts
for 20 m of fence

Shopping list

ItemBuyNote
Posts10 postsat most 2.4 m apart; about 600 mm in the ground
Rails, 2.4 m lengths27 rails3 per bay at 1800 mm high
Palings, 100 mm wide200 palingsedge to edge
Post Mix concrete, 20 kg bags (post holes)20 bags2 bags a hole, for a hole 2 × the post width
  • The 2-bag figure is Bunnings Post Mix advice for a hole 2 × the post width. A wider or deeper hole needs more bags.
How this was worked out
  1. Panels (bays): length ÷ post spacing, rounded up
    20000 ÷ 2400 = 9 bays
  2. Posts: bays + 1
    9 + 1 = 10 posts
  3. Rails: bays × rails per bay
    9 × 3 = 27 rails
  4. Palings: length ÷ (paling width + gap), rounded up
    20000 ÷ (100 + 0) = 200 palings
  5. Concrete for posts: posts × bags per hole
    10 × 2 = 20 bags

How it is worked out

The calculator on this site determines quantities by dividing fence length by post spacing, rounding up to find the number of panels, and then adding one post (bays + 1). According to Timber Queensland TDS 20 Residential Timber Fences, rails 100 by 38 millimetres allow 2400 millimetres maximum post spacing, or 2100 millimetres with 75 by 38 millimetres rails. The same source states that fences over 1200 millimetres and up to 1800 millimetres high require three rails, while two rails are used for paling fences up to 1200 millimetres high. Palings are laid edge to edge by default, with 100 millimetres and 75 millimetres being commonly used sizes. For post holes, Bunnings Easy Mix Post Mix technical data sheet specifies using approximately two 20-kilogram bags per post hole, based on a hole width equal to two times the width or diameter of the post. Timber Queensland TDS 20 Residential Timber Fences notes that posts sit about 600 millimetres deep for fences 1200 to 1800 millimetres high, and 450 millimetres up to 1200 millimetres high.

What changes the answer

The total number of posts changes when you alter the overall length of the fence or the spacing between the posts. Changing the paling width or the gap between palings changes the number of palings required without altering the post count. Altering the height of the fence changes the number of rails per bay, shifting requirements between two rails for heights up to 1200 millimetres and three rails for heights over 1200 millimetres and up to 1800 millimetres. Altering the post hole dimensions changes the concrete required, as the two-bag figure assumes a hole width of two times the post width. If you dig a wider or deeper hole, you will need more bags of concrete. Check your product label or supplier if your hole is wider or deeper than 2 × the post width.

Quick reference table

LengthPostsRails (2.4 m)Palings (100 mm)Post Mix Concrete (20 kg bags)
10 m6 posts15 rails100 palings12 bags
20 m10 posts27 rails200 palings20 bags
30 m14 posts39 rails300 palings28 bags
50 m22 posts63 rails500 palings44 bags

Worked example

To see how the numbers are generated, look at the calculation for a 10-metre fence. First, the calculator finds the number of panels by dividing length by post spacing and rounding up, using the formula panels equal length divided by post spacing rounded up, which evaluates as 10000 divided by 2400 to give 5 bays. Next, it finds the post count by adding one to the panel count, using the formula posts equal bays plus 1, which evaluates as 5 plus 1 to equal 6 posts. Rails are calculated by multiplying the number of bays by rails per bay, using the formula bays multiplied by rails per bay, evaluated as 5 multiplied by 3 (the calculator's starting value of three rails per bay, which Timber Queensland TDS 20 gives for fences over 1200 mm and up to 1800 mm high) to equal 15 rails. Palings are determined by dividing length by the sum of paling width and gap and rounding up, evaluated as 10000 divided by 100 plus 0 to equal 100 palings. Concrete is calculated by multiplying posts by bags per hole, evaluated as 6 multiplied by 2 to equal 12 bags.

Common mistakes

One arithmetic error is forgetting to add the final end post to the total, which happens when someone divides length by bay size and stops without adding one. Another mistake is assuming that post mix requirements stay constant if you dig holes wider than the 2 × post width the Bunnings Easy Mix Post Mix technical data sheet gives, or deeper holes. Treating the default edge-to-edge paling layout as mandatory without accounting for timber shrinkage leads to miscounts if you decide to leave a gap. Failing to match the rail count to the fence height results in ordering the wrong number of rails, as fences over 1200 millimetres and up to 1800 millimetres high require three rails, while paling fences up to 1200 millimetres high need two rails, according to Timber Queensland TDS 20 Residential Timber Fences. Finally, confusing panel spacing limits, such as mixing up the 2400 millimetres allowance for 100 by 38 millimetres rails with the 2100 millimetres limit for 75 by 38 millimetres rails, causes incorrect bay layouts.

Frequently asked questions

How many posts do I need for a 20-metre fence?

The calculator gives 10 posts for a 20-metre fence when using 2.4-metre bays.

How are panels calculated?

Panels are calculated by dividing the total fence length by the post spacing and rounding up.

How much concrete do I need per post?

Bunnings Easy Mix Post Mix technical data sheet specifies using approximately two 20-kilogram bags per post hole for a hole width equal to two times the post width.

How many rails do I need for a fence over 1200 millimetres high?

Timber Queensland TDS 20 Residential Timber Fences states that fences over 1200 millimetres and up to 1800 millimetres high require three rails.

What is the default paling gap?

Palings are laid edge to edge by default with a gap of zero millimetres, though you can adjust this if timber shrinkage is a factor.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
fence timber post spacing max2.4 mVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: rails 100 x 38 mm allow 2400 mm max post spacing (2100 mm with 75 x 38 mm rails).
fence timber rails up to 12002 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: two rails for paling fences up to 1200 mm high.
fence timber rails over 12003 railsVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: fences over 1200 mm and up to 1800 mm high require three rails.
fence paling width 100100 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling width 7575 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: commonly used paling sizes are 100 x 15 mm and 75 x 15 mm.
fence paling gap default0 mmEditable defaultPalings are laid edge to edge by default. Timber shrinks, so many builders leave a small gap; type your own gap.
fence steel panel width 2sheet1,582 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 1582 mm with 2 infill sheets.
fence steel panel width 3sheet2,350 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 2350 mm with 3 infill sheets (post spacing = panel width).
fence steel panel width 4sheet3,100 mmVerified 2026-11-18Lysaght fence and gate installation guide (non-cyclonic) Table 6.1: panel width 3100 mm with 4 infill sheets.
concrete post bags per hole2 bags (20 kg)Verified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: use approximately two 20 kg bags per post hole.
concrete post hole width factor2 x post widthVerified 2026-11-18Bunnings Easy Mix Post Mix technical data sheet: hole width = 2 x width or diameter of the post.
fence timber post depth600 mmVerified 2026-11-18Timber Queensland TDS 20 Residential Timber Fences: posts about 600 mm deep for fences 1200-1800 mm high (450 mm up to 1200 mm).

Keep reading