Fencing & decking
How many decking boards do I need?
You need 86 decking boards for a 4.8 x 3.6 metre deck when using 90 mm hardwood boards with 3 mm gaps.
Shopping list
| Item | Buy | Note |
|---|---|---|
| Decking boards, 90 mm wide, 2.4 m long | 86 boards | 39 rows of 2.0 boards, 3 mm gaps |
| Joists, 3.6 m long | 11 joists | at most 500 mm apart |
| Screws or nails (two per board per joist) | 944 fixings | check your board maker's fixing advice |
- Gap between boards: 3 mm for hardwood (ATFA). Use at least 5 mm close to the ground or over a slab. Joist spacing: no more than 500 mm for Hardwood, 19 mm (WoodSolutions).
- Bearers, posts, footings and deck height need a design to AS 1684. This calculator counts the deck surface only. Check with your council whether you need approval.
How this was worked out
- Rows of boards:
width ÷ (board width + gap), rounded up
3600 ÷ (90 + 3) = 39 rows - Boards per row:
length ÷ board length
4.8 ÷ 2.4 = 2 boards - Boards:
rows × boards per row × (1 + waste), rounded up
39 × 2.00 × 1.10 = 85.8 boards - Joists:
length ÷ joist spacing, rounded up, + 1
4800 ÷ 500 + 1 = 11 joists - Fixings:
rows × joists × fixings per crossing × (1 + waste)
39 × 11 × 2 × 1.10 = 943.8 fixings
Understanding the calculation
To work out the quantity of materials for your deck, the calculator takes the deck dimensions alongside the board size. For a 4.8 x 3.6 metre deck, it first finds the number of rows needed to cover the width. It adds the board width of 90 mm to the 3 mm gap, then divides the 3600 mm width by that 93 mm, rounding up. The deck length is then divided by the board length of 2.4 m to find the boards per row. The board count multiplies rows by boards per row by (1 + waste), using a 10% waste allowance for cuts and defects, and rounds up. Joists come from the length divided by the joist spacing of 500 mm, rounded up, plus 1. Fixings are rows times joists times two fixings per crossing times (1 + waste). For the 17.3 m² deck in this guide, the calculator returns 86 boards, 11 joists and 944 fixings.
Factors influencing your material count
Several variables change the final tally of your shopping list. The gap between boards matters: the ATFA Residential Timber Decks guide gives a 3 mm gap for hardwood or cypress boards up to 90 mm wide, not close to the ground. The same guide gives a 5 mm gap for softwood boards and for 130 mm hardwood. The calculator's warning is to use at least 5 mm close to the ground or over a slab. Joist spacing also changes the joist count and the number of fixings. WoodSolutions TDG 21 Table 2 gives a maximum joist spacing of 500 mm for 19 mm hardwood decking. WoodSolutions and ATFA say at least two nails or screws per board at each joist crossing. The board length of 2.4 m, the board width of 90 mm and the deck length and width also change the count.
Summary of deck material requirements
The following table shows the material requirements for different deck sizes from the calculator, using 90 mm wide, 2.4 m long hardwood boards with 3 mm gaps.
| Deck Dimensions | Boards Required | Joists Required | Fixings Required |
|---|---|---|---|
| 4.8 m x 3.6 m | 86 | 11 | 944 |
| 6.0 m x 4.0 m | 121 | 13 | 1,259 |
| 3.0 m x 3.0 m | 46 | 7 | 509 |
The 4.8 x 3.6 m deck covers 17.3 m² and uses 3.6 m joists. The 6 x 4 m deck covers 24.0 m² and uses 4 m joists, and the 3 x 3 m deck covers 9.0 m² and uses 3 m joists.
Worked example
To calculate the requirements for a 4.8 x 3.6 metre deck, follow these steps. First, find the number of rows by dividing the width (3600 mm) by the combined width of the board and gap (90 mm + 3 mm), which gives 38.7, rounded up to 39 rows. Next, calculate the boards per row by dividing the deck length (4.8 m) by the board length (2.4 m), resulting in 2 boards. To find the total boards, multiply the 39 rows by 2 boards per row, then by 1.10, because the formula includes (1 + waste) for the 10% allowance. That gives 85.8, rounded up to 86 boards. For joists, divide the length (4800 mm) by the 500 mm spacing to get 9.6, round up to 10, then add 1, resulting in 11 joists. Finally, multiply 39 rows by 11 joists by 2 fixings by 1.10 to get 943.8, which is 944 fixings. The shopping list is 86 boards 90 mm wide and 2.4 m long, 11 joists 3.6 m long, and 944 screws or nails.
Common mistakes
A frequent error is adding waste twice. The board and fixing counts already include a 10% allowance, because the formula multiplies by (1 + waste); do not add waste again. Another mistake is ignoring the gap: the calculator uses 3 mm for 90 mm hardwood, and the ATFA guide gives 5 mm for softwood. Also check the maximum joist spacing of 500 mm for 19 mm hardwood, as the joist count is worked out from the spacing. Always check your board thickness against the WoodSolutions spacing table, because other materials have different maximums. Cypress is 400 mm for 19 mm boards and 450 mm for 21 mm boards. Treated softwood is 400 mm for 19 mm boards and 450 mm for 22 mm boards. Finally, do not use the unrounded working figures (85.8 boards or 943.8 fixings) as your purchase quantity; round up to 86 boards and 944 fixings.
Frequently asked questions
Why does the calculator add 10% to my total?
The 10% is the calculator's starting value, an editable allowance for cuts and defects.
Can I use a 5 mm gap for my hardwood deck?
The calculator uses 3 mm for 90 mm hardwood, and its warning says to use at least 5 mm close to the ground or over a slab. The ATFA guide also gives 5 mm for softwood boards.
How many fixings do I need per board?
WoodSolutions and ATFA say at least two nails or screws per board at each joist crossing. The calculator multiplies rows by joists by two, then by 1.10 for waste.
What is the maximum joist spacing for hardwood?
WoodSolutions says the maximum joist spacing for 19 mm hardwood decking is 500 mm.
Does this calculator include the structure under the deck?
No. This calculator counts the deck surface only. Bearers, posts, footings and deck height need a design to AS 1684.
Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.