EnoughToGet CalculatorsGuides

Roofing & cladding

How many weatherboards do I need?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

For the 12 × 2.7 m wall, allow 57 Linea 180 mm boards; the smaller 8 × 2.4 m wall needs 34.

Try itWeatherboard cladding: enter your own sizes
m
Add up every wall you are cladding.
m
m²
Doors and windows.
Effective cover is the width a board covers after the overlap, from James Hardie.
Each external corner takes a corner trim up the full height.
%
You need
57 boards
32.4 m² of Linea 180 mm

Shopping list

ItemBuyNote
Linea 180 mm boards, 4200 mm long57 boards150 mm effective cover
External corner trim, 3600 mm lengths4 lengthsaluminium boxed corner, Linea guide
  • James Hardie says effective cover is for guidance: measure on site. Fixings, flashings and the exact overlap depend on the product and your wall: follow the installation guide.
How this was worked out
  1. Wall area: length × height − openings
    12 × 2.7 − 0 = 32.4 m²
  2. Cover of one board: effective cover × board length
    0.15 × 4.2 = 0.63 m²
  3. Boards: area × (1 + waste) ÷ cover of one board, rounded up
    32.40 × 1.10 ÷ 0.630 = 56.57 boards
  4. Corner trim: corners × (height ÷ trim length, rounded up)
    4 × ceil(2.7 ÷ 3.6) = 4 lengths

How the count is worked out

The calculator works from wall area, then uses the effective cover and board length to estimate the board count. For Linea 180 mm, James Hardie’s installation guide gives an effective cover of 150 mm after a 30 mm lap, with boards 4200 mm long. The calculator converts those measurements to a cover of 0.63 m² per board.

The wall area formula is length × height − openings. The board formula is area × (1 + waste) ÷ cover of one board, rounded up. In the two Linea 180 mm examples below, the waste multiplier is 1.10, so the count already includes a 10% allowance. Do not add another allowance to the rounded purchase count. The calculator also estimates external corner trim separately from the board count.

Quick reference table

These two results use Linea 180 mm boards that are 4200 mm long. The smaller wall has less area and therefore needs fewer boards, while both estimates include the calculator’s corner-trim quantity.

Wall areaLinea 180 mm boardsExternal corner trim
32.4 m²57 boards4 lengths
19.2 m²34 boards4 lengths

For the larger wall, the shopping list is 57 boards and 4 lengths of external corner trim, each 3600 mm long. For the smaller wall, it is 34 boards and 4 lengths of the same trim. The calculator rounds board counts up to whole boards and calculates trim separately. James Hardie says effective cover is for guidance, so measure on site; fixings, flashings and the exact overlap depend on the product and wall, so follow the installation guide.

Worked example

For the 12 × 2.7 m wall, begin with the area calculation: length × height − openings, using 12 × 2.7 − 0. The result is a wall area of 32.4 m².

Next, calculate the cover of one board: effective cover × board length, using 0.15 × 4.2. That gives 0.63 m² per board. The calculator then applies its board formula: area × (1 + waste) ÷ cover of one board, rounded up, using 32.40 × 1.10 ÷ 0.630. This gives 56.57 boards. Because the formula includes the 10% waste allowance, 56.57 already includes that allowance; it is not a pre-waste count. Rounding up gives a purchase quantity of 57 boards.

The corner-trim calculation is separate: corners × (height ÷ trim length, rounded up), using 4 × ceil(2.7 ÷ 3.6). The result is 4 lengths of trim. It does not change the board count.

What changes the answer

Wall length and height affect the area used in the calculation, while openings are subtracted in the area formula. The first example uses 12 × 2.7 m and 0 openings; the smaller example uses 8 × 2.4 m and 0 openings. Their resulting areas are 32.4 m² and 19.2 m², respectively. If the measured wall or openings differ, the calculated area and board estimate can change.

The effective cover also matters: the Linea 180 mm calculation uses 150 mm of cover, not the full board width. James Hardie’s installation guide describes that cover after a 30 mm lap. The calculator applies a 10% waste allowance in these examples. OzTradieCalc describes 8 to 10% for a plain wall and higher ranges for walls with openings or complex shapes; the allowance can therefore affect the estimate. Check your product label or supplier if the product or measurements differ.

Common mistakes

A common arithmetic mistake is to divide the wall area by the board’s full width instead of its effective cover. For Linea 180 mm, the calculation uses 150 mm effective cover after a 30 mm lap, giving 0.63 m² of cover for a 4200 mm board. Using a different cover changes the count, so check the product label or supplier if the product differs.

Another mistake is treating 56.57 as a count that still needs the waste allowance. The formula multiplies by 1.10 before rounding, so that figure already includes the allowance; round it up to 57 rather than adding 10% again. Also keep units consistent: the calculator’s board-length calculation uses metres, with 0.15 × 4.2. Finally, do not combine corner trim with boards: the 4 trim lengths are calculated separately from the board quantity.

Frequently asked questions

How many boards do I need for a 12 × 2.7 m wall?

The calculator estimates 57 Linea 180 mm boards for a 32.4 m² wall, including its 10% waste allowance.

How many boards does the smaller wall need?

For an 8 × 2.4 m wall with an area of 19.2 m², the estimate is 34 boards.

Does the count include waste?

Yes. The formula uses a 1.10 multiplier, so its 10% allowance is already included before the count is rounded up.

Why use 150 mm rather than 180 mm?

James Hardie’s installation guide gives 150 mm as the effective cover for Linea 180 mm after a 30 mm lap. The full board width is not the cover used in the calculation.

How much corner trim is estimated?

The calculator estimates 4 lengths of external corner trim for each wall example. Each length is 3600 mm; check your product label or supplier if your trim differs.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
cladding linea150 cover120 mmVerified 2026-11-18James Hardie Linea installation guide: Linea 150 mm board, 4200 mm long, effective cover 120 mm after a 30 mm lap.
cladding linea180 cover150 mmVerified 2026-11-18James Hardie Linea installation guide: Linea 180 mm board, 4200 mm long, effective cover 150 mm after a 30 mm lap.
cladding linea length4,200 mmVerified 2026-11-18James Hardie Linea installation guide: Linea boards are 4200 mm long.
cladding stria325 cover300 mmVerified 2026-11-18James Hardie Stria Cladding Smooth 325 mm: effective width 300 mm, lengths 3000 and 4200 mm.
cladding stria405 cover380 mmVerified 2026-11-18James Hardie Stria Cladding Smooth 405 mm: effective width 380 mm, lengths 3000 and 4200 mm.
cladding stria length4,200 mmVerified 2026-11-18James Hardie Stria Cladding Smooth: lengths 3000 and 4200 mm (the longer length is used).
cladding plank230 cover205 mmVerified 2026-11-18James Hardie HardiePlank 230 mm board: effective cover 205 mm after a 25 mm overlap, 4200 mm long.
cladding plank300 cover275 mmVerified 2026-11-18James Hardie HardiePlank 300 mm board: effective cover 275 mm after a 25 mm overlap, 4200 mm long.
cladding plank length4,200 mmVerified 2026-11-18James Hardie HardiePlank boards are 4200 mm long.
cladding stria325 pack60 boards/packVerified 2026-11-18James Hardie Stria Cladding Smooth 325 mm: 60 pieces per pack.
cladding stria405 pack40 boards/packVerified 2026-11-18James Hardie Stria Cladding Smooth 405 mm: 40 pieces per pack.
cladding plank pack120 boards/packVerified 2026-11-18James Hardie HardiePlank 230 and 300 mm: 120 pieces per pack.
cladding corner length3,600 mmVerified 2026-11-18James Hardie Linea installation guide: aluminium external slimline boxed corner, 3600 mm long.
cladding snap corner length3,000 mmVerified 2026-11-18James Hardie External Cladding Technical Specification: aluminium snap-on corner, 3000 mm long, 2 pieces per set (used for Stria and HardiePlank).
cladding waste10 %Editable defaultOzTradieCalc (calculator site): 8 to 10% for a plain wall, 10 to 12% with a few windows and a door, up to 15 to 20% for complex walls. No manufacturer figure found.