EnoughToGet CalculatorsGuides

Landscaping

How many turf rolls do I need?

By the EnoughToGet teamUpdated 2026-11-184 min readSources and assumptions

To cover a 40 m² lawn with a 5% waste allowance, you need 42 turf rolls.

Try itTurf: enter your own sizes
m
Type metres, for example 8.5.
m
mm
Leave at 0 if you are laying onto good soil already.
%
Curved edges and garden beds waste more.
You need
42 rolls
40.0 m² of lawn

Shopping list

ItemBuyNote
Turf rolls42 rolls1 m² a roll
Topsoil, 100 mm deep4 m³about 5.60 t
  • Most Australian turf rolls cover 1 m² (Musturf, AG Turf Supplies), but check with your grower: some sell slabs or different roll sizes. Lay turf the day it is delivered.
How this was worked out
  1. Lawn area: length × width
    8 × 5 = 40 m²
  2. Rolls: area × (1 + waste) ÷ roll area, rounded up
    40.00 × 1.05 ÷ 1 = 42 rolls
  3. Topsoil: area × depth ÷ 1000
    40.00 × 100 ÷ 1000 = 4 m³

How the turf roll count is worked out

The calculator starts with the lawn area, which is length × width. For a space 8 metres long and 5 metres wide, that gives 40 m². The roll count then comes from area × (1 + waste) ÷ roll area, rounded up: 40.00 × 1.05 ÷ 1 = 42 rolls. The 1.05 is 1 + 0.05, so the 5% allowance sits inside that figure already; the formula does not add it a second time. Topsoil is calculated on its own line, area × depth ÷ 1000: 40.00 × 100 ÷ 1000 = 4 m³. The same three steps produce every result in this guide, and the "rounded up" instruction is why the roll count always ends on a whole roll rather than a fraction.

What changes the answer

Three inputs move the roll count. The first is lawn area: 40 m² gives 42 rolls, 60 m² gives 63 and 100 m² gives 105, each with the same 5% allowance applied. The second is the roll area used as the divisor. Musturf and AG Turf Supplies say most turf rolls in Australia cover 1 m², but check with your grower, because some sell slabs or different roll sizes — a different roll area changes the divisor and therefore the count. The third is the waste percentage, which is editable; the calculator's starting value is 5%, an allowance for cuts and edges. Topsoil depth, set at 100 mm, is editable too, but it changes only the topsoil volume, never the number of rolls.

Turf rolls and topsoil for 40, 60 and 100 m² lawns

The figures below come from the calculator with a 1 m² roll area and a 5% waste allowance already included in the roll count.

Lawn areaTurf rollsTopsoil at 100 mm deep
40.0 m²42 rolls4 m³
60.0 m²63 rolls6 m³
100.0 m²105 rolls10 m³

The 60 m² row is a lawn 10 metres by 6 metres, and the 100 m² row is 10 metres by 10 metres. In each case the roll count is the area multiplied by 1.05 and divided by 1, and the topsoil is the area multiplied by 100 and divided by 1000.

Worked example

Take the first example: a lawn 8 metres long and 5 metres wide.

Step one, lawn area: 8 × 5 = 40 m².

Step two, rolls: the formula is area × (1 + waste) ÷ roll area, rounded up, so 40.00 × 1.05 ÷ 1 = 42 rolls. Because the 1.05 already contains the 5% allowance, those 42 rolls are the full purchase — nothing extra is added on top.

Step three, topsoil: the formula is area × depth ÷ 1000, so 40.00 × 100 ÷ 1000 = 4 m³.

The purchase is therefore 42 rolls, plus 4 m³ of topsoil at 100 mm deep. With 1 m² rolls, 42 rolls would cover 42 m², which is 2 m² more than the 40 m² lawn — the room the cuts and edges use up.

Rounding, units and the waste allowance

The roll formula carries a "rounded up" instruction, so a count that lands between two whole rolls is pushed to the higher one. In the three examples here the arithmetic falls exactly — 40 × 1.05 = 42, 60 × 1.05 = 63 and 100 × 1.05 = 105 — so there is no fraction to round, but a lawn with an awkward area will produce one.

The waste figure is a percentage, 5% at the calculator's starting value, and it enters as (1 + waste), that is 1.05. Treat that figure as the inclusive one and read it as "area plus 5%".

Units matter in the topsoil line. Length and width go in as metres, giving square metres, and the depth goes in as millimetres, which is why the step divides by 1000 to reach cubic metres. Check your product label or supplier for the roll size you are actually buying.

Common mistakes

Ordering the plain area with no allowance is the first: 40 rolls for a 40 m² lawn leaves nothing for cuts and edges, which is exactly what the 42-roll figure covers.

Adding the waste twice is the second. The 1.05 in area × (1 + waste) ÷ roll area already includes the 5%, so treating a "plus 5%" as a further step after 42 rolls over-orders.

Dividing by the wrong roll area is the third. Musturf and AG Turf Supplies put most Australian rolls at 1 m², but some growers sell slabs or different roll sizes, and if the divisor does not match what is delivered, the count will be wrong. Check with your grower.

Finally, keep the units straight: metres for length and width, millimetres for depth, and the division by 1000 for cubic metres of topsoil.

Frequently asked questions

How many turf rolls do I need for a 60 m² lawn?

63 rolls, using 1 m² rolls and the 5% waste allowance; the same lawn needs 6 m³ of topsoil at 100 mm deep.

Do the 42 rolls for a 40 m² lawn include the waste allowance?

Yes. The 1.05 in area × (1 + waste) ÷ roll area already contains the 5%, so the 42 rolls are the finished count and nothing is added afterwards.

How much topsoil does a 100 m² lawn need?

10 m³ at a depth of 100 mm, from 100.00 × 100 ÷ 1000.

How deep should the topsoil be?

The calculator starts at 100 mm for a new lawn, and that depth is editable, so change it if your own plan differs.

How heavy is that topsoil?

Australian Native Landscapes gives topsoil a density of 1.4 t/m³, so 4 m³ works out at 5.6 tonnes, 6 m³ at 8.4 tonnes and 10 m³ at 14 tonnes.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
turf roll area1 m2/rollVerified 2026-11-18Musturf and AG Turf Supplies: most turf rolls in Australia cover 1 square metre.
turf waste5 %Editable defaultEditable allowance for cuts and edges. No Australian grower figure found: a common turfing rule of thumb.
landscape topsoil lawn depth100 mmEditable defaulttypical topsoil depth for a new lawn, rule of thumb, editable
landscape density topsoil1.4 t/m3Verified 2026-11-18Australian Native Landscapes product weights FAQ: topsoil 1.4 t/m3.